Features

• VisiFlo color-coded version consists of stainless steel or ceramic orifice in polypropylene body.
• Maximum operating pressure 300 psi (20 bar).
• Spray angle is 80º at 100 psi (7 bar).
• Finely atomized spray pattern provides thorough coverage.
• TX-VS1 and TX-VS2 available in VisiFlo color-coded stainless steel only.

Typical Applications

• Excellent for post-emerge contact herbicides, fungicides, and insecticides. Assures finely atomized spray droplets reach target areas.
• Good for use with defoliants and foliar fertilizers at pressures 40 psi (3 bar) and above.M

TXA / TXB

Features

• Maximum operating pressure 300 psi (20 bar).
• Spray angle is 80º at 100 psi (7 bar).
• Finely atomized spray pattern provides thorough coverage.
• Longer wear life.
• Resists corrosion.
• Accepts more abrasive pesticide formulation.
• Polypropylene body for use with corrosive materials and ceramic insert.
• Popular nozzle sizes fit most sprayers.
• Incorporates ISO color-coding scheme.

Typical Applications

• Excellent for post-emerge contact herbicides, fungicides, and insecticides. Assures finely atomized spray droplets reach target areas.
• Good for use with defoliants and foliar fertilizers at pressures 40 psi (3 bar) and above.

Features

• Made of stainless steel.
• Large orifices and open internal passages help minimize clogging problems.
• Nozzle caps are interchangeable.
• 1/4″ NPT or BSPT (M) inlet connection.

Features

• Large droplets to reduce drift.
• Excellent spray distribution over a range of pressures 15-40 psi (1-3 bar).
• Ideal for use on rigs with sprayer controllers.
• Wide spray angle allows use on 40″ (100 cm) spacings.
• Available in VisiFlo color-coding system in all stainless steel or Celcon with stainless steel vane.
• Can be used with CP25607-*-NY for Quick TeeJet connection.

Optimum Spray Height
FullJet nozzles should be angled 30º-45º from vertical for uniform spray distribution.

For spraying pesticides at higher pressures and flow rates. Especially suitable for wettable powders and other abrasive chemicals. Larger capacity nozzles are also used in air blast sprayers.

Features

• Produce smaller droplets for thorough coverage with contact pesticides and foliar applications.
• Maximum spray pressure to 300 psi (20 bar).
• Hollow cone spray pattern produced by cores #13, 23, 25, 45, and 46.
• Full cone spray pattern produced by cores #31, 33, 35, and 56.

Orifice Discs
Available in a variety of sizes and materials. Ceramic for increased wear life, hardened stainless steel, stainless steel, and polymer.

Ceramic sizes available:
DCER-2 through DCER-8, DCER-10.

Cores
Standard cores are made of brass. Also available in ceramic, hardened stainless steel, aluminum, and nylon. All cores, with the exception of ceramic, are made with rear “nibs”. Be sure core is always placed with the nib facing the nozzle body.

Ceramic sizes available:
DC13-CER, DC23-CER, DC25-CER,
DC31-CER, DC33-CER, DC35-CER,
DC45-CER, DC46-CER, DC56-CER.

Strainer Note: For nozzles using orifice disc numbers 1, 1.5, and 2; or core numbers 31 and 33, slotted strainer number 4514-20 equivalent to 25 mesh screen size is required. For all other larger capacity discs and cores, slotted strainer number 4514-32 equivalent to 16 mesh screen size is required.

Features

• Used for high volume applications.
• Large, round orifice reduces clogging.

The revolutionary Quick Turbo FloodJet nozzle combines the precision and uniformity of a flat spray nozzle with the clog-resistance and wide angle pattern of flooding nozzles. It uses an exclusive new design to increase droplet size and distribution uniformity.

Features

• Patented turbulence chamber creates a dramatic improvement in pattern uniformity.
• Pre-orifice design produces larger droplets for reduced drift.
• Large, round orifice reduces clogging.
• Grooved side molding for automatic alignment with any quick-connect coupler.
• Stainless steel with color-coding for easy size identification.
• Nozzle can be mounted between 0º and 45º.
• Available in standard sizes from 1.5 gpm up to 24.0 gpm (6.84 l/min to 94.73 l/min) at pressures of 10-40 psi (1-3 bar).

Features

• Direct replacement for plastic hollow cone, low-drift nozzles.
• Very large droplets.
• More precise flow and distribution pattern.
• Large orifice reduces clogging.
• Recommended operating pressure range is 25-75 psi (1.5-5 bar).
• Can be used with Quick TeeJet cap QJ4676-*-NYR.
• Stainless steel or polymer construction.

QJ4676-90-1/4-NYR

• 90º fitting attaches to Quick TeeJet bodies – 1/4″ female threaded outlet.
• Simple installation of TurfJet nozzles on vertical nozzle bodies.
• Nylon construction.

• Excellent spray distribution for uniform coverage along the boom.
• Nozzle design incorporates a pre-orifice to produce larger droplets for less drift.
• Large, round orifice reduces clogging.
• Stainless steel or polymer with VisiFlo color-coding band for easy size identification.
• Can be used with CP25600-*-NYR Quick TeeJet cap and gasket for automatic alignment.

QCT Cam-Loc Adapter

• Provides easy changeover from high capacity to lower capacity nozzles.
• Adapter fits standard 3/4″ quick connect Cam-Loc holders.
• Corrosion-resistant stainless steel and polypropylene construction.
• Rated up to 100 psi (7 bar).
• Use QJT-NYB tp retrofit to Quick TeeJet.

Features

• TeeJet Off-Center spray tips are commonly installed in double and single swivel nozzle bodies.
• Because these bodies are adjustable for angular positions, wide spray swaths are easily obtained.
• Recommended spraying pressures are 30–60 psi (2 -4 bar).
• Available in stainless steel or brass material.

Features

• Suggested for post-directed application with hose drops.
• 150º series stainless steel and brass.